Particle size is an important consideration when selecting wood powder activated carbon. It can influence powder handling, dispersion, contact with the treated liquid, and the subsequent filtration process.
Powdered activated carbon is often described using a mesh size and a passing percentage. For applications that require more detailed information, a particle size distribution report can provide additional insight into the size range of the powder.
HANYAN can provide particle size distribution information, including D10, D50, and D90, to support customer evaluation and product development.
What Is Particle Size Distribution?
A powder sample contains particles of different sizes. Particle size distribution describes how those sizes are distributed within the sample, rather than representing the entire powder with a single value.
A distribution report may include a curve and several characteristic values, such as D10, D50, and D90. These values help describe the finer, middle, and coarser portions of the measured distribution.
Particle size should not be confused with pore size. Particle size describes the dimensions of the powder particles, while pore size refers to the small spaces within the activated carbon structure.
What Do D10, D50, and D90 Mean?
The meaning of these values depends on the measurement method and the basis used in the report. For example, when the results are expressed as a cumulative volume distribution:
| Parameter | Meaning in a Volume-Based Distribution |
|---|---|
| D10 | 10% of the measured particle volume is represented by particles smaller than this size. |
| D50 | 50% of the measured particle volume is represented by particles smaller than this size. It is also known as the volume median size. |
| D90 | 90% of the measured particle volume is represented by particles smaller than this size. |
These values describe positions in the measured distribution. They do not mean that 10%, 50%, or 90% of the particles by number are below those sizes.
To interpret a report correctly, check the units, distribution basis, measurement method, and sample preparation conditions.
Why Look Beyond Mesh Size?
Mesh size and passing percentage are useful for describing how much powder passes through a specified sieve. However, a passing percentage at one sieve size does not show the complete distribution of particles below that size.
Two samples may both meet the same sieve specification but have different proportions of fine and coarse particles. A particle size distribution report can help customers compare those differences in greater detail.
Sieve analysis and particle size distribution measurements provide different information. Their results should be interpreted according to their respective methods rather than treated as directly interchangeable.
How Can Particle Size Affect an Application?
Particle size can influence several stages of a liquid-phase treatment process:
- Dispersion: Particle size and other powder characteristics can affect how carbon disperses in a liquid.
- Contact and adsorption rate: Particle size may influence the time needed for substances in the liquid to reach adsorption sites inside the carbon.
- Filtration: The particle size distribution can affect how the carbon is retained and separated by the filtration equipment.
- Powder handling: The proportion of fine particles may be relevant to dust control and handling procedures.
These effects depend on the complete application, including the liquid being treated, mixing conditions, carbon dosage, and filtration system. A finer powder is therefore not automatically the best choice for every process.
Using Particle Size Data to Support Product Development
Particle size distribution data can help customers communicate their requirements more clearly. For example, a customer may need to evaluate both the typical particle size and the proportion of relatively coarse material in a powder.
HANYAN can provide particle size distribution information, including D10, D50, and D90, to help customers review product characteristics. Together with application testing and other quality indicators, these data can support product selection and development.
Our technical team can discuss particle size requirements alongside other specifications, such as adsorption performance, moisture, ash, and the customer’s filtration process.
Discuss Your Requirements with HANYAN
If you are looking for wood powder activated carbon with specific particle size requirements, please share your target parameters, application, and preferred test method with us.
HANYAN can support product evaluation and discuss the particle size information and reports available for your project.
Contact us: enquiry@hanyancarbon.com
References
- HORIBA Scientific, Understanding and Interpreting Particle Size Distribution Calculations .
- Malvern Panalytical, Definition and Measurement Methods of Particle Size Distribution .
Article Keywords: wood powder activated carbon particle size, activated carbon particle size distribution, D10 D50 D90 activated carbon, powdered activated carbon particle size, wood activated carbon testing, activated carbon mesh size, particle size distribution report


